Results 1 to 10 of 16
6LikesThread: jig to saw scale blanks
LinkBack URL
About LinkBacks-
05-13-2009, 05:49 PM #1Senior Member
- Join Date
- Dec 2006
- Location
- Burkburnett TX
- Posts
- 3,095
Thanked: 2392
jig to saw scale blanks
Here is an easy to make jig that will allow you to cut out scale blanks from planed stock. The jig will allow for accurate work without years of practice or the cost of power tools. It is a section of 2X4 with one wide side and one small side made square and flat. There are two magnet holders and magnets on the side. The magnets are right below the surface. The magnets will hold the saw square and allow you to saw. The two screws in the top just have the points barely sticking out on the bottom to provide a nonslip grip. The jig works well with pull style saws. Lee Valley sells the magnets.
The only challenging part is getting two the sides square. You can do it with a hand plane or talk somebody with a jointer into doing it for you. Or find a square table leg or furniture part at the thrift store you can cut up
CharlieLast edited by spazola; 05-13-2009 at 10:08 PM. Reason: fonix
-
The Following 23 Users Say Thank You to spazola For This Useful Post:
0livia (05-13-2009), adrspach (05-17-2009), AirColorado (06-27-2009), Cove5440 (04-23-2012), Del1r1um (05-13-2009), dnjrboy (05-13-2009), FacialDirt (07-30-2014), jakoblah (05-13-2009), jeness (04-16-2012), JoeSomebody (04-23-2012), Jonah (05-20-2013), Leighton (05-13-2009), MichaelC (04-14-2012), moostashio (05-27-2014), PaddyX21 (04-14-2012), pjrage (05-13-2009), randydance062449 (05-15-2009), Slamthunderide (04-14-2012), Slartibartfast (05-13-2009), smythe (05-18-2009), STF (04-14-2022), Walt (05-13-2009), ZeroCool (04-16-2012)
-
05-13-2009, 06:22 PM #2Beard growth challenged
- Join Date
- Feb 2009
- Location
- Berlin
- Posts
- 1,928
Thanked: 402
You devil!
Thats nifty!
-
05-13-2009, 07:21 PM #3Cream Huffer
- Join Date
- Aug 2008
- Location
- Edmonton, Alberta
- Posts
- 573
Thanked: 74
If you have any ingenuity left, can you whip up a jig for resawing 3/8 knife handle stock into 1/8 ths scales? That would be awesome.
-
05-13-2009, 07:29 PM #4Comfortably Numb
- Join Date
- Jan 2009
- Location
- Charlotte, NC
- Posts
- 2,095
Thanked: 668
sweet man, i'm going to set one up next weekend!
-
05-13-2009, 08:09 PM #5Senior Member
- Join Date
- Jun 2008
- Location
- Budapest, Hungary
- Posts
- 106
Thanked: 17
Grrreat!!!
I was thinking the other day on something similar, but You were faster.
Good job!
-
05-13-2009, 09:01 PM #6Cream Huffer
- Join Date
- Aug 2008
- Location
- Edmonton, Alberta
- Posts
- 573
Thanked: 74
What are the screws for?
-
05-13-2009, 09:30 PM #7Beard growth challenged
- Join Date
- Feb 2009
- Location
- Berlin
- Posts
- 1,928
Thanked: 402
Here we go.The two screws in the top just have the points barely sticking out on the bottom to provide a nonslip grip.
-
05-13-2009, 10:41 PM #8Senior Member
- Join Date
- Jul 2008
- Location
- Knoxville, TN
- Posts
- 874
Thanked: 312
I like it!
-
05-13-2009, 10:53 PM #9I still have my face!
- Join Date
- Apr 2009
- Location
- Westminster, CO
- Posts
- 162
Thanked: 21
Very clever! Jigs make the world a better place.
-
05-15-2009, 01:39 AM #10Hones & Honing
- Join Date
- May 2005
- Location
- Saint Paul, Minnesota, United States
- Posts
- 7,973
- Blog Entries
- 1
Thanked: 2204
Well done! This will help a lot of guys.
Randolph Tuttle, a SRP Mentor for residents of Minnesota & western Wisconsin
Reply With Quote