Page 1 of 2 12 LastLast
Results 1 to 10 of 19
Like Tree33Likes

Thread: Honing is Super Easy

  1. #1
    Senior Member
    Join Date
    Nov 2014
    Location
    Sacramento
    Posts
    309
    Thanked: 135

    Default Honing is Super Easy

    Until its not. Yesterday it was not easy. After my wild success with touching up my Boker using Aaron's (yes Aaron, it is now forever your method!) progression on an Arkie finisher, I couldn't wait to start on the other 10 razors in my current rotation. Next up was a little near-wedge Christopher Johnson that my brother (my picker, he loves flea markets) found for me. This pretty little razor in bone scales was my first almost wedge and cleaned up decently and took a surprisingly easy edge when I first got it (one layer of tape and what a nice, silent shaver). Another 20 minutes or so and more shaving bliss.
    Well, that little wedge sucked down on that dry translucent so hard before I knew it up came the spine and whoops; what the heck just happened. Nothing to see here folks, pretend that didn't happen and lets move on. Well, if it grabbed on the dry stone it was like glue when it sucked down on the water. Yep, flipped her again. Nothing a few more strokes won't fix right? No. Remember Ground Hog Day when Bill Murray is racing through each repeating day trying to recapture that magic date? Well, that was me. Three cycles of dry to oil and that sweet little shaver wasn't happy with me. I had to walk away after over an hour (probably two). Hanging hair test? Yeah, no. Even added another layer of tape. Not happening. Today I had hoped to post more success pics and shave happiness. I did have shave happiness but at the edge of a different razor.
    Tomorrow I'll do a reboot and try again.
    I took a pic of my fail; we do like pics! The darker arkie is my hard; I brought it out on circuit 3 to see if a few strokes on that would bring the edge back. No.
    Even a bad day on the stones sure beats mowing the lawn.
    Name:  Fail hone.jpg
Views: 416
Size:  47.9 KB

  2. #2
    Senior Member blabbermouth RezDog's Avatar
    Join Date
    Feb 2013
    Location
    Haida Gwaii, British Columbia, Canada
    Posts
    14,383
    Thanked: 4820

    Default

    You should check it with a loupe and give it a good squint in order to decide how to fix it. You may have to make a few steps back in this dance.
    earcutter and Gasman like this.
    It's not what you know, it's who you take fishing!

  3. The Following User Says Thank You to RezDog For This Useful Post:

    Paulbuck (08-19-2018)

  4. #3
    Senior Member blabbermouth ScoutHikerDad's Avatar
    Join Date
    May 2010
    Location
    Upstate South Carolina
    Posts
    3,308
    Thanked: 987

    Default

    Yikes, Paul-I hope I didn't cause this. But yes, a blade (some grinds more than others) that is already close can start to dig in surprisingly quickly with this method. That is when you have to start being more careful, and maybe add a couple drops of dish-washing liquid before proceeding. These finer arks are so hard and dense (and your edge is so fine before we even get there) that there is not much room for error.

    Sounds like yours might need to just go back and reset the bevel on a 4k or something before proceeding again with caution. I'm sure you will sort it out.
    earcutter likes this.

  5. The Following User Says Thank You to ScoutHikerDad For This Useful Post:

    Paulbuck (08-19-2018)

  6. #4
    Senior Member
    Join Date
    Nov 2014
    Location
    Sacramento
    Posts
    309
    Thanked: 135

    Default

    Quote Originally Posted by ScoutHikerDad View Post
    Yikes, Paul-I hope I didn't cause this.
    Aaron,
    Pretty sure this one is all on me!! The method is sound, its the execution needs work.
    I'm an all arkie guy and only use 4 stones and a Norton Crystolon that I use for prepping them (thanks Steel). Heavy work is done (slowly) on a Washita and then I progress up through a soft, hard (prepping these stones with the cystolon is the key, and gives me a mini progression with each stone) and then the translucent. The edge is actually pretty close so today I was going to prep the hard with the fine side of the crystolon (the hard is well burnished at the moment) and use two layers of tape and normal oil based honing. That should do the trick. Then I'll go to the trans dry and carefully finish it off.
    I think that little wedge will be happy with me again (I hope).

  7. #5
    Senior Member blabbermouth outback's Avatar
    Join Date
    Mar 2015
    Location
    Akron, Ohio
    Posts
    11,924
    Thanked: 4300

    Default

    I'm a four stone guy, as well. I bevel set with a Chosera, but the rest of the progression is all naturals which consists of the Washita, Thurigan, and Escher B/G. B/D

    I must say, there's something magical about the Washita, and its abilities to act as different stones when used with different lubes. ( water, oil, lather, glycerin, dry, edge leading, spine leading, ect. )
    Mike

  8. #6
    Senior Member
    Join Date
    Nov 2014
    Location
    Sacramento
    Posts
    309
    Thanked: 135

    Default

    Got to spend a little time today on that Christopher Johnson and Co. The hard brought the edge right back and all went well. Popping hairs easily and I'm anticipating a nice shave.
    I find a little booze helps too
    Name:  1N2A9501.jpg
Views: 342
Size:  47.4 KB

  9. #7
    Senior Member Brontosaurus's Avatar
    Join Date
    Feb 2011
    Location
    Les Vosges, France
    Posts
    924
    Thanked: 185

    Default

    Interesting thread, and delicious-looking stones. I've used the Arkansas line for a while and have not tried the Crystalon combo to "dress" the stones, using emery cloth instead. If you want to experiment further with oil, I would suggest trying first cold-pressed, extra-virgin olive oil for something heavy and Singer sewing machine oil for something light. My stones with razors are always hand-held, so the idea of a 6" x 2" Crystalon combo appeals to me on the 6" x 2" and smaller Arkansas stones I use. And once the fine side of the Crystalon combo has been broken in, it may be good for grunt work honing as needed.
    Striving to be brief, I become obscure. --Horace

  10. #8
    Senior Member blabbermouth ScoutHikerDad's Avatar
    Join Date
    May 2010
    Location
    Upstate South Carolina
    Posts
    3,308
    Thanked: 987

    Default

    Quote Originally Posted by Paulbuck View Post
    Got to spend a little time today on that Christopher Johnson and Co. The hard brought the edge right back and all went well. Popping hairs easily and I'm anticipating a nice shave.
    I find a little booze helps too
    Name:  1N2A9501.jpg
Views: 342
Size:  47.4 KB
    Oh, man-Were we separated at birth or something? That is probably my favorite bourbon, and I'm overdue for a bottle! I too sometimes like a little splash while honing.

  11. #9
    Senior Member kelbro's Avatar
    Join Date
    May 2008
    Location
    N. Carolina
    Posts
    1,352
    Thanked: 181

    Default

    Quote Originally Posted by ScoutHikerDad View Post
    Oh, man-Were we separated at birth or something? That is probably my favorite bourbon, and I'm overdue for a bottle! I too sometimes like a little splash while honing.
    But you shouldn't cut the 4 Roses 50/50 like you do with other hone lubes...

  12. #10
    lobeless earcutter's Avatar
    Join Date
    Feb 2012
    Location
    Kansas
    Posts
    4,864
    Thanked: 762

    Default

    Who was the guy who got me to make a little coti slurry on top of my black? Was that you Hiker?

    I still do it. It’s still all yum.
    David

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •