Results 1 to 9 of 9
  1. #1
    Spacesaver Vicious's Avatar
    Join Date
    Jan 2013
    Location
    Orange County, California
    Posts
    43
    Thanked: 6

    Question Nicking the strop...

    As I'm sure it's a normal for a new-to-straight-razor-shaving guy to nick his leather hanging strop I pose this question; is it possible to harm the razor with a slight nick in the leather? Mine is a 2" red Latigo hanging strop and despite slow even strokes before my first few shaves with little pressure and never rolling on the edge, I managed to nick the leather on the edge near where I start a lap. At first the one or two nicks didn't seem so severe so I made extra special care to not to repeat the mistake to avoid making more or make the ones already there worse. However, last week after stropping my 5/8 Dovo 40 laps on the canvas strop I started in on the leather, again, being very careful, but I noticed a streak on the leather following the path the razor, almost like the razor was scraping the surface. Confused, I looked at the edge and sure enough, little pieces of leather just hangin out where they shouldn't. "Okay," I thought, "it appears I've nicked my brand new razor and/or rolled the edge." Wasn't sure how, but chalked it up to my less-than-novice skills. A couple days later I take a look at the leather strop again and it occurred to me that the nicks on the blade and those on the leather matched up; where I finish a lap.

    Unfortunately I cannot load pictures as a reference as I've only my dinosaur flip-phone with POS camera.

    So have I possibly ruined a strop that will forever pose a threat to any razor* I may use on it? Should I just abandon the strop I have in favor of a new one or can it be saved? I'm considering going to either a paddle or a loom to avoid rolling the edge as is, but that would be down the road when finances are better. Any advice would be greatly appreciated.


    *Regardless of strop issues, I'll be getting the razor re-honed next week.
    Just sayin...

  2. #2
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    Hard to say without seeing it but if there are no divots, flaps ...... nothing you can feel with your fingers sticking up I wouldn't think it would damage a razor if you are stropping properly. If there is anything hit it with pumice stone or light sandpaper and knock it down. Glue flaps with contact cement if they are large enough.

  3. The Following User Says Thank You to JimmyHAD For This Useful Post:

    Vicious (01-31-2013)

  4. #3
    Senior Member ccase39's Avatar
    Join Date
    Nov 2012
    Location
    Slidell, La
    Posts
    570
    Thanked: 43

    Default

    I found it a lot easier and a lot better for my strop to place it on the kitchen counter and strop that way. Just lay it flat and go slow. I nicked my strop a few times and did what Jimmy said followed by a little strop conditioner and everything was cool.

  5. The Following User Says Thank You to ccase39 For This Useful Post:

    Vicious (01-31-2013)

  6. #4
    Senior Member moehal's Avatar
    Join Date
    Nov 2012
    Location
    United Arab Emirates
    Posts
    165
    Thanked: 11

    Default

    Quote Originally Posted by Vicious View Post
    As I'm sure it's a normal for a new-to-straight-razor-shaving guy to nick his leather hanging strop I pose this question; is it possible to harm the razor with a slight nick in the leather? Mine is a 2" red Latigo hanging strop and despite slow even strokes before my first few shaves with little pressure and never rolling on the edge, I managed to nick the leather on the edge near where I start a lap. At first the one or two nicks didn't seem so severe so I made extra special care to not to repeat the mistake to avoid making more or make the ones already there worse. However, last week after stropping my 5/8 Dovo 40 laps on the canvas strop I started in on the leather, again, being very careful, but I noticed a streak on the leather following the path the razor, almost like the razor was scraping the surface. Confused, I looked at the edge and sure enough, little pieces of leather just hangin out where they shouldn't. "Okay," I thought, "it appears I've nicked my brand new razor and/or rolled the edge." Wasn't sure how, but chalked it up to my less-than-novice skills. A couple days later I take a look at the leather strop again and it occurred to me that the nicks on the blade and those on the leather matched up; where I finish a lap.

    Unfortunately I cannot load pictures as a reference as I've only my dinosaur flip-phone with POS camera.

    So have I possibly ruined a strop that will forever pose a threat to any razor* I may use on it? Should I just abandon the strop I have in favor of a new one or can it be saved? I'm considering going to either a paddle or a loom to avoid rolling the edge as is, but that would be down the road when finances are better. Any advice would be greatly appreciated.


    *Regardless of strop issues, I'll be getting the razor re-honed next week.
    you said that there seems to be a trail as the razor slides over the strop. since you have a 2" strop, im guessing that during your x-trokes the point of your razor is the part that scrapes the leather? i had the same problem on my poor man's strop and pressure was the culprit. try doing x-strokes with no pressure but only the weight of the razor. this video could also be very helpful, there are other great videos too by Lynn Abrahams but this can relate more to your problem.



    hope it helps and happy shaving!
    hal.

  7. The Following User Says Thank You to moehal For This Useful Post:

    Vicious (01-31-2013)

  8. #5
    Senior Member
    Join Date
    Jan 2013
    Posts
    122
    Thanked: 3

    Default

    Ok I am having the same issue and just purchased a new strop. I had flaps the touched the blade and I think that it dulled it. Would the new strop take care of it or do I need to take it to the Norton 8k?

  9. #6
    Junior Member
    Join Date
    Oct 2012
    Posts
    7
    Thanked: 1

    Default

    I've done the same with mine. I'm more concerned with the blade. Do I need to get it re-honed now?

  10. #7
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    Quote Originally Posted by pbsd View Post
    Ok I am having the same issue and just purchased a new strop. I had flaps the touched the blade and I think that it dulled it. Would the new strop take care of it or do I need to take it to the Norton 8k?
    Quote Originally Posted by DirkDD View Post
    I've done the same with mine. I'm more concerned with the blade. Do I need to get it re-honed now?
    If further correct stropping won't bring it back than honing would be what is needed.

  11. #8
    Senior Member moehal's Avatar
    Join Date
    Nov 2012
    Location
    United Arab Emirates
    Posts
    165
    Thanked: 11

    Default

    Quote Originally Posted by JimmyHAD View Post
    If further correct stropping won't bring it back than honing would be what is needed.
    +1 on that,
    although, before you decide that you really rolled the edge. consider shaving a cheek with it as you would with a sharp blade, with proper angles and no pressure at all. if that does not work, and you need to apply pressure then you surely need to have it honed again. the edge hitting a d-ring or the leather square would most like need to be rehoned, but i dont think one or two false laps on the strop could destroy the edge. do correct me if i am wrong.

  12. #9
    Spacesaver Vicious's Avatar
    Join Date
    Jan 2013
    Location
    Orange County, California
    Posts
    43
    Thanked: 6

    Default

    I took some sand paper to my strop and nicks are not noticeable anymore, so that's good. As for the blade, well, I took a look at it with a magnifying glass (though not very powerfull) and I've definitely rolled the edge in the middle (definitely poor technique on my part) with a couple nicks near the heel. Not sure how I did the nicks, I haven't smacked a D-Ring or the faucet (I wipe with a clean towel instead of rinsing) so I'm at a loss. Dropping it off tomorrow for honing. Thanks again all for the advice!
    Just sayin...

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •