Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 27
Like Tree6Likes

Thread: Oiling my only razor?

  1. #11
    Senior Member sheajohnw's Avatar
    Join Date
    Jul 2010
    Location
    Rye, New Hampshire, United States
    Posts
    392
    Thanked: 83

    Default

    Always keep water/lather out of the blade pivot area. The pivot area is hard to wipe dry and is a prime location for water stains and rust to begin. The only time I had a stain/rust issue beginning was when I let water get in the pivot area of a carbon steel razor. Preventing stains and rust is a lot easier than trying to remove these blemishes.

    After shaving, I rinse the razor's blade below the shank/pivot in hot running tap water and wipe dry. The heat helps dry the razor. Keep the blade tilted down to prevent water from running into the pivot area.

    I then strop the dried razor and wipe the blade and between the scales with a small rag slightly damp with camellia oil. The oil damp rag is stored between uses in a small plastic former pill container always ready for use that I keep next to my strops. The wipe rag can also be used to wipe carbon steel kitchen knives. The rag is only slightly damp with oil, but leaves a thin barely visible film on the wiped blades and does not leave fingers wet with oil.

    Any good steel protecting oil such as a gun oil would work, but camellia or mineral oil are often used because they are eatable oils and any residues that may remain on a blade wiped clean of oil should not adversely affect ones face. Camellia oil is sold by tool and knife vendors and has been used on Japanese swords.

    I wipe my straight razor blades and scales once in a while with Renaissance Wax, but a silicon wipe for firearms preservation would also be good. Wipe preservatives off the blade immediately before restropping done before the next razor use. Storing razors in humid heavily used bathrooms may be risky for rust.

    Always wiping your razor with an oily rag after use or touching metal as a ritual (as is done with firearms) will ensure that you will never pickup your razor that has not been used for a while and wonder where the rust came from. For me, looking at an unnecessary cosmetic blemish caused by neglect before each shave, especially one caused by me, is an unpleasant reminder that detracts from each shaving experience. I expect to see normal wear and tear on a well used razor.

    HTH
    Last edited by sheajohnw; 03-06-2012 at 12:00 PM.
    pmburk and MrAlex2You like this.

  2. #12
    Junior Member
    Join Date
    Feb 2012
    Posts
    20
    Thanked: 1

    Default

    Quote Originally Posted by pmburk View Post

    Yes, YMMV. When I had just one razor, I carefully wiped it dry not only on the blade, but between scales and around the pivot pin. Then I used the Camellia oil. Then the next day, I wiped off the oil and use the razor. Now I have 12 razors in rotation, I keep all my razors oiled. If I still only had one razor, I would oil it after each use. To me, the oil is cheap insurance.

    What kind of oil? Well in my opinion, I would stay away from anything with petroleum base or distillate. I recall reading posts from members using 3 In 1 Oil, I don't think that is very good for your skin. The same applies to WD-40, it has petroleum distillates too. Both can burn or irritate some skin types. I suggest you use a natural or organic oil. Some shavers like to use olive oil, Camellia oil (that's what I use), cooking oil, mineral oil, and I know a couple guys who use Renaissance Wax to protect their razors. We have a poster in this thread who uses Chamomile oil, great idea!
    I think I am going to purchase some Camellia oil; I'm going to see if I can't pick it up somewhere here in the STL area. Thanks for the advice!

  3. #13
    I shave with a spoon on a stick. Slartibartfast's Avatar
    Join Date
    Jan 2009
    Location
    Stay away stalker!
    Posts
    4,578
    Thanked: 1262
    Blog Entries
    1

    Default

    Just pick up some mineral oil.. Any store with a pharmacy section will have it in the laxative section

  4. #14
    Senior Member
    Join Date
    Sep 2010
    Posts
    2,169
    Thanked: 220

    Default

    It never hurts to use a bit of oil after every use, but I don't think that everybody has to. A lot depends on the razor's usage and the humidity levels. I guess if you start to notice rust, it's time to use oil. If you do use it, I just use mineral oil and it seems to work good.

  5. #15
    Junior Member
    Join Date
    Feb 2012
    Posts
    20
    Thanked: 1

    Default

    I'm sure I can find mineral oil. What about this? Spring Valley Pharmaceutical Grade Tea Tree Oil - Walmart.com

  6. #16
    Senior Member pmburk's Avatar
    Join Date
    May 2011
    Location
    Perry Hall, MD.
    Posts
    578
    Thanked: 58

    Default

    Quote Originally Posted by MrAlex2You View Post
    I'm sure I can find mineral oil. What about this? Spring Valley Pharmaceutical Grade Tea Tree Oil - Walmart.com
    I went to the link you provide, I see no reason why you can't use it. Heck, give it a try and let everyone know how it works out for your razor.

  7. #17
    Senior Member
    Join Date
    Sep 2010
    Posts
    2,169
    Thanked: 220

    Default

    Quote Originally Posted by MrAlex2You View Post
    I'm sure I can find mineral oil. What about this? Spring Valley Pharmaceutical Grade Tea Tree Oil - Walmart.com
    I don't see why not, tea tree oil is a mild oil that uses include polishing wood & mold control, I have never heard of anybody using it on their razor but I'm sure it should protect it. P.S. Walmart should carry mineral oil as well.

  8. #18
    < Banned User >
    Join Date
    Feb 2011
    Posts
    1,256
    Thanked: 194

    Default

    If you love your razor and don't want to see rust...take a few seconds and oil it...as for what to use? I have used vegetable oil for 2 years on my dovo with no problems...You can get a 4 litre jug at most grocery stores for about $2.00 lol

  9. #19
    < Banned User >
    Join Date
    May 2011
    Location
    Decatur, Georgia
    Posts
    430
    Thanked: 48

    Default

    would be nice a light machine oil but in a mini pump spray that doesn't fan out too much. lots of clippercide comes out to the amount that actually is needed or hits the blade.

  10. #20
    what Dad calls me nun2sharp's Avatar
    Join Date
    Feb 2008
    Location
    Kansas city area USA
    Posts
    9,172
    Thanked: 1677

    Default

    Alex, I live in the KC area and I do not oil my blades unless I am putting one up for a while. If you have central air and heat there should be little problem.Another thing I do is that I NEVER rinse a blade under the faucet. I will use a dry towel to wipe off lather. No water means no rust and keeping the blade away from the faucet means no dings to hone out. Good luck and enjoy SRP.
    It is easier to fool people than to convince them they have been fooled. Twain

Page 2 of 3 FirstFirst 123 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •