Page 1 of 3 123 LastLast
Results 1 to 10 of 30
  1. #1
    Junior Member
    Join Date
    Aug 2010
    Posts
    10
    Thanked: 0

    Default Beginner ATG shaving

    Hey guys.

    I've shaved about 20 times or so with a straight now, and the experience has generally been better every time. When i shave with the grain, i have hardly any problems and i think i'm starting to get the hang of it.

    However, when i try to shave against the grain, it's a different story. I find ATG shaving on my neck and upper lip very uncomfortable and slightly painful. I get lots of red blotches and irritation. This is only on my neck and lip, when i shave ATG on my cheeks and sideburns it's completely fine.

    What am I doing wrong ? I'm pretty sure my razor is sharp enough, and i use a very shallow angle when shaving ATG ( nearly pinning back or blade on skin) and using light pressure. I also stretch the skin, and this doesn't seem to help.

  2. #2
    Senior Member Str8nDE4RAD's Avatar
    Join Date
    Aug 2010
    Location
    Hickory, NC
    Posts
    233
    Thanked: 30

    Default

    Some say it takes time for your skin to adjust to shaving ATG. Personally I have done it a few times and end up with razor burn most of the time and the razor skipping up my neck sometimes. It is not an easy technique to get right the first few times. Keep with it and just be cautious, if it pulls any or starts to hurt just STOP.

    Personally I just don't do it and am working on my stretching and XTG shaving. I may try it again later when I feel my stretching is good enough to try.

  3. The Following 2 Users Say Thank You to Str8nDE4RAD For This Useful Post:

    oldschooltools (11-11-2010), pinklather (11-12-2010)

  4. #3
    Senior Member simpleman's Avatar
    Join Date
    Sep 2010
    Posts
    361
    Thanked: 110

    Default

    I never had irritation but it was less comfortable than wtg passes the first couple times tried atg.

  5. #4
    Still learning markevens's Avatar
    Join Date
    Jun 2010
    Posts
    1,043
    Thanked: 240

    Default

    It takes your skin some time to get used to a straight,(not to mention you getting used to using it) during which time going ATG can be very uncomfortable.

    I waited about a month before going ATG. I found that skin stretching was more vital there than before, and restropping helped a lot as well.

  6. The Following User Says Thank You to markevens For This Useful Post:

    oldschooltools (11-11-2010)

  7. #5
    Getting there....
    Join Date
    Oct 2010
    Location
    Near Utrecht, NL
    Posts
    272
    Thanked: 50

    Default

    I noticed(with the above) that the angle of the blade on ATG is really important. The wiki explains this nicely.


  8. The Following 2 Users Say Thank You to BrickBag For This Useful Post:

    Nepsis (11-12-2010), oldschooltools (11-11-2010)

  9. #6
    Member
    Join Date
    Dec 2009
    Location
    Columbus, Ohio
    Posts
    65
    Thanked: 17

    Default

    +1 on the angle. I also like to use light buffing strokes on tough areas like my upper lip.

    Buffing
    This is a technique, mainly to be used during the ATG pass. The blade is moved back and forth in short strokes over the skin, without lifting it. Pressure needs to be extremely low. The first part of the stroke cuts the hairs and the second, withdrawing part of the stroke smears an amount of lather back on the skin, preparing for the next stroke that will cut the hair even closer. This is only useful on dense parts of the beard where thick whiskers require more than one stroke to be gradually cut till the "zero"-level. The sound produced by the razor (if it’s a hollow ground one) will guide you through the process, steadily moving ahead while making short overlapping strokes. It is best reserved as a last resort, to achieve ultimate smoothness on renitent spots.

  10. The Following 2 Users Say Thank You to nickymcc For This Useful Post:

    oldschooltools (11-11-2010), pinklather (11-12-2010)

  11. #7
    Senior Member Alembic's Avatar
    Join Date
    Dec 2009
    Location
    Clarkston MI
    Posts
    1,527
    Thanked: 488
    Blog Entries
    1

    Default

    I ATG every day - but not my upper lip. I can do it, but it's not necessary. I do a WTS and an XTG East to West and West to East. At the end I have a great shave there.

    The key to ATG really is the blade angle. I drop the blade almost flat against my skin and lift slightly into the stroke. If the blade angle is too steep, you will hook onto the whisker and it will pull the blade straight into the base of the follicle, which results in your razor burn.

    And remember - NO PRESSURE.

  12. The Following User Says Thank You to Alembic For This Useful Post:

    oldschooltools (11-11-2010)

  13. #8
    Real Live Barber chay2K's Avatar
    Join Date
    Jun 2010
    Location
    Salt Lake City, UT
    Posts
    454
    Thanked: 115

    Default

    In addition to all of the above advice, I would just say that skin stretching is also a huge factor here. I didn't get comfortable ATG passes, especially on my lip, until I got proficient at the stretch.

  14. The Following User Says Thank You to chay2K For This Useful Post:

    oldschooltools (11-11-2010)

  15. #9
    Junior Member
    Join Date
    Aug 2010
    Posts
    10
    Thanked: 0

    Default

    Thanks for the info on buffing and angle guys.
    Alembic, when you say lift into the stroke, do you mean i should lift the razor away from my skin towards the end of the stroke ?

  16. #10
    Senior Member Alembic's Avatar
    Join Date
    Dec 2009
    Location
    Clarkston MI
    Posts
    1,527
    Thanked: 488
    Blog Entries
    1

    Default

    Quote Originally Posted by CreativeBass View Post
    Thanks for the info on buffing and angle guys.
    Alembic, when you say lift into the stroke, do you mean i should lift the razor away from my skin towards the end of the stroke ?
    Take a look at that 5 degree angle shown for ATG. So what I do is lay the blade flat - 0 degrees and lift the spine slightly up towards that 5 degree angle as I BEGIN the stroke, making slight adjustments to in on the fly. If I feel it hook onto whiskers I lower the angle, If I feel it skipping over whiskers I raise the angle. It should feel smoothas you make the pass. If you feel it dig, your angle is too steep.

    Hope that helps.


  17. The Following User Says Thank You to Alembic For This Useful Post:

    oldschooltools (11-11-2010)

Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •