Page 1 of 2 12 LastLast
Results 1 to 10 of 17
  1. #1
    Junior Member
    Join Date
    Apr 2010
    Location
    Folsom, CA
    Posts
    24
    Thanked: 3

    Default Wiping the blade properly?

    During my first go at shaving this weekend, I found myself a little worried about damaging the edge while wiping the blade dry after rinsing off the soap lather and whiskers. Instead I just lightly set the blade down on a towel on each side.

    Would I be damaging the edge if I wipe the blade from heel to toe sandwiched between two layers of towel? I thought about doing this but envisioned the blade being so sharp that it would catch on the towel as I dragged it through.

    I think I saw a video of a guy wiping his blade on a sponge at one point...

    What is the best way to dry or wipe off a blade as you progress through the shave?

    -Stub

  2. #2
    Indisposed
    Join Date
    Oct 2008
    Posts
    6,038
    Thanked: 1195

    Default

    I'm more of a rinser than a wiper, but when I do find occasion to wipe I'll use a very light stropping motion on a towel (often the one I'm wearing around my waist after my shower), being careful not to fold the edge. It has always worked for me as I have yet to roll an edge.

  3. #3
    The Electrochemist PhatMan's Avatar
    Join Date
    Apr 2009
    Location
    Hastings, UK
    Posts
    1,714
    Thanked: 527

    Default

    Stubbles,

    I pinch the razor between the fingers & towel as far as the belly of the blade (about 1/4 inch from the edge) and wipe; then as Ryan says, a light stropping motion to clean the edge.

    Have fun !

    Best regards

    Russ

  4. #4
    They call me Mr Bear. Stubear's Avatar
    Join Date
    Jul 2009
    Location
    Alton, UK
    Posts
    5,715
    Thanked: 1683
    Blog Entries
    3

    Default

    I actually do both. I rinse the blade to get most of the gunk off it, then I pinch the razor between some tissue and wipe it along its length from heel to toe.

  5. #5
    Senior Member leadduck's Avatar
    Join Date
    May 2007
    Location
    Concord, NH
    Posts
    1,287
    Thanked: 274

    Default

    I use Stubear's method of rinse then wipe. With the spine in the middle of the towel, I come as close to the edge as I dare without letting the towel touch it. Occasionally, if I think the edge may need more, I'll give it one or two laps on the linen of my strop. I've never had to leave it out to air dry and I've never had rust.

  6. #6
    Senior Member AnarchoPhil's Avatar
    Join Date
    Aug 2009
    Location
    Dothan, AL
    Posts
    195
    Thanked: 46

    Default

    using the thumb is a bad idea

  7. #7
    The Assyrian Obie's Avatar
    Join Date
    Mar 2009
    Location
    Milwaukee, WI
    Posts
    11,145
    Thanked: 2755

    Default Wiping the blade properly?

    Gentlemen:

    I rinse he blade in hot water, wipe the blade with a towel, followed by Kleenex (both between forefinger and thumb), strop it (15/25) and then oil it.

    Regards,
    Obie

  8. The Following User Says Thank You to Obie For This Useful Post:

    jpm7676 (04-21-2010)

  9. #8
    Texas Guy from Missouri LarryAndro's Avatar
    Join Date
    Jul 2009
    Posts
    1,135
    Thanked: 252

    Default

    Conceptually, I don't think there is any danger in using a towel or tissue to wipe clean a blade. Leather is much more abrasive than cloth. What could wiping off a blade with cloth, sliding horizontally along its length, do to a blade compared to multiple vertical passes on leather?

  10. #9
    -- There is no try, only do. Morty's Avatar
    Join Date
    Feb 2010
    Location
    SE PA
    Posts
    501
    Thanked: 167

    Default

    Quote Originally Posted by LarryAndro View Post
    What could wiping off a blade with cloth, sliding horizontally along its length, do to a blade compared to multiple vertical passes on leather?
    I have a 3/4" slice in one of my hand towels that I was using to wipe my razor off with because I wasn't being careful. (I'm REALLY lucky I didn't cut further through and slice my fingers open!) When the honing instructions in the Wiki states that the TNT is to be used only during setting the bevel because in later honing stages it dulls the edge, cutting my towel likely dulled the edge somewhat also.

    After I watched Chimensch's 30 anniversary shave video, I copied his use of a wet sponge in the sink to wipe the lather off. My sink is smaller than his so the point of my Black Diamond spike seemed dangerously close to the basin wall. I gave up on that strategy.

    I thought about how a barber lays a dry towel on the shoulder of his client and wipes the lather off on that. So I pick up a dry towel in my open hand now and wipe the lather off on it the same way a barber would. A very short stropping motion.
    Namaste,
    Morty -_-

  11. #10
    Texas Guy from Missouri LarryAndro's Avatar
    Join Date
    Jul 2009
    Posts
    1,135
    Thanked: 252

    Default

    Quote Originally Posted by Morty View Post
    I have a 3/4" slice in one of my hand towels that I was using to wipe my razor off with...
    Yes, but we're talking about what it can do to a blade. That being said, GOOD POINT!

    I realize that wiping a blade horizontally on a cloth might damage the blade, although I think not. Even if so, it would be very slight and inconsequential I believe. I believe this to be the case both from experience, and from the logic of it... If vertical stropping on leather is gentle with mild results on the blade, won't one or two swipes horizontally with a soft cloth be even more inconsequential?

    The bigger consideration for me is keeping my blade free of buildup and spots, locations where the blade can become rusted. I consider it much more important to clean the blade well than any worry about insignificant (in my opinion) damage to the blade.

    For this reason, I always clean my blades thoroughly after every shave with a cloth, using a fair amount of force between thumb and forefinger. The cloth is draped over the spine. And, the cloth comes down almost to the bevel, or right at the bevel. (My stropping cleans the bevel.) If the cloth even touches the edge, there will be very little contact.
    Last edited by LarryAndro; 04-20-2010 at 06:25 PM.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •