Results 1 to 10 of 10
  1. #1
    Junior Member bradyjfrey's Avatar
    Join Date
    Dec 2009
    Location
    San Francisco, CA
    Posts
    26
    Thanked: 2

    Default Slightly damaged blade

    I made a silly mistake- reached over my sink with the blade in the right hand, and gently hit the faucet dead on. It was subtle enough that it barely made a sound, but enough that it made a small 1/16" length nick easily seen in the light, although it's barely dented. Here's a brief iPhone video, although very difficult to see:
    http://bradyjfrey.com/bf/blade.mov

    Suggestions for fixing this? Better to send it in and have it re-honed or is there a home method for working this out? Since it's at the end, it doesn't often touch my face, but enough to cause me a concern.

  2. #2
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    Faucet dings are the most common fix for a Honemeister followed closely by the infamous Bathroom floor slam

    Any one of the competent guys listed in the classifieds can fix it...
    or if you have the proper stones/hones I might could talk you through it...

  3. #3
    Junior Member bradyjfrey's Avatar
    Join Date
    Dec 2009
    Location
    San Francisco, CA
    Posts
    26
    Thanked: 2

    Default

    I'd be game to try it myself, but you'd have to even go so far as to tell me what stones I'd need to get!

    Sounds like a good idea to get a backup blade too, just in case I repeat this issue...

  4. #4
    The original Skolor and Gentileman. gugi's Avatar
    Join Date
    Aug 2007
    Posts
    17,410
    Thanked: 3906
    Blog Entries
    1

    Default

    well here's my version of how to do it yourself.

    you will need 1k 4k and 8k hones, or if you want to spend several hours (let's say 5) to remove the chip on a slower hone 4k and 8k would do.
    so the norton 4000/8000 combo would be the very minimum.

    first you lap the hone (see the wiki tutorial for doing it with sandpaper).
    then you would put electrical tape on the spine (i'd say 3 layers so that when you put a bit more pressure on the blade it'll still work well).
    then on the 1000 or 4000 you hone in circles or up and down the hone switching sides every say 50 strokes and using the same amount of pressure and number of strokes on each side until the chip is gone. this is the time consuming process. (get a cheap magnifier to make sure you don't stop prematurely). at this point raising slurry on the hone is the way to speed up the process, the only problem is that I wouldn't use sandpaper for that because I'm afraid it'll leave some sandpaper grits in and those are coarse and damaging to the edge.
    once the chip is gone you would use only one layer of tape (or no tape at all) and very very little pressure to set the bevel so that it is very sharp (it's a ti, so it should be popping armhairs, or at least shave effortlessly at skin level). this is the most critical step, no point of moving further until yo accomplish it.
    once that's done, do 50 x-pattern strokes on the 4k hone, at this point the strokes have to be light. then do another 30 on the 8k hone and that's it.
    realistically it may not shave too well, so perhaps the best way at this point is to use the pyramid method (read on it in the wiki). the lighter, more uniform, and consistent your strokes are the better the razor will shave.
    Last edited by gugi; 02-05-2010 at 09:38 PM.

  5. The Following 2 Users Say Thank You to gugi For This Useful Post:

    59caddy (02-06-2010), UtahRootBeer (02-07-2010)

  6. #5
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    Amazon has the entire Norton starter set for $120 shipped free...

    http://www.amazon.com/Norton-Waterst...7&sr=8-1-fkmr0

    That has all the stones and more than what Gugi just explained about...and you get a lapping stone,,, maybe not a great one, but it does work...
    Last edited by gssixgun; 02-05-2010 at 09:44 PM.

  7. #6
    < Banned Scammer >
    Join Date
    Jun 2009
    Location
    Sunny California!
    Posts
    466
    Thanked: 125

    Default

    If you have the skills and equipment to hone it out, i'd say go for ith. Otherwise, you may want to consider sending it out to a honemeister.

  8. #7
    Junior Member bradyjfrey's Avatar
    Join Date
    Dec 2009
    Location
    San Francisco, CA
    Posts
    26
    Thanked: 2

    Default

    Quote Originally Posted by sapito318 View Post
    If you have the skills and equipment to hone it out, i'd say go for ith. Otherwise, you may want to consider sending it out to a honemeister.
    I'd have to say you're right - although I do want to learn this, I don't think I want to gamble with my nice new blade.

    Thanks gssixgun & gugi for the great advice; I'll purchase that set and start learning on some backup blades, so the knowledge is very much appreciated and helpful. Looks like I'll be sending in my blade for another hone.

  9. #8
    Senior Member ziggy925's Avatar
    Join Date
    Oct 2009
    Location
    Colorado
    Posts
    325
    Thanked: 36

    Default

    Okay. Here's my two cents. You won't be the first to do this and you sure won't be the last, so don't feel bad.

    I've done this twice and I've been able to strop it out. Look at the blade with a magnifier or microscope. The damage on my blade looked like a tiny dent -- no chipping. If the blade is not chipped you can try to strop it but you have to be careful so you don't damage your strop. Maybe start with the backside and very short strokes. If the back of your strop is pasted even better.

    If the blade leaves a mark on the strop it's going to leave a mark on your face. Send it to a pro. If the strop looks clean you can try to strop it out and just use caution when you shave with it.

    I could see both small nicks under a strong light but my strop showed no damage and I noticed no problems shaving. The blade has been sharpended since, but I got a lot of good shaves out of it before sending it in.

  10. The Following User Says Thank You to ziggy925 For This Useful Post:

    alex357 (02-08-2010)

  11. #9
    Junior Member bradyjfrey's Avatar
    Join Date
    Dec 2009
    Location
    San Francisco, CA
    Posts
    26
    Thanked: 2

    Default

    Quote Originally Posted by ziggy925 View Post
    I've done this twice and I've been able to strop it out. Look at the blade with a magnifier or microscope. The damage on my blade looked like a tiny dent -- no chipping. If the blade is not chipped you can try to strop it but you have to be careful so you don't damage your strop. Maybe start with the backside and very short strokes. If the back of your strop is pasted even better.
    Sounds like what mine looks like then - I've been shaving with it all week without problems, but I've also been consciously trying to avoid that back edge a bit just in case.

    I have been trying to strop it out, and it looks to be improving but it's still obvious. I'll ride it out for a few days; purchased a cheaper end Dovo on Friday to back this one up, so I'll do a switch-a-roo once that guy comes in, and send this guy out.

    Unfortunately, I've been getting a poor shave out of it lately, and I'm hoping that's due to technique issues on my part, and not a larger problem with the blade. We shall see!

  12. #10
    Junior Member bradyjfrey's Avatar
    Join Date
    Dec 2009
    Location
    San Francisco, CA
    Posts
    26
    Thanked: 2

    Default

    Green paste... that stuff rocks. Damn near took the whole thing out in 20 passes, and sharpened my blade something nice, thanks for the recommendation!

    Now I have to learn when to use that and when not too - I imagine I could abuse it, and it shouldn't be an every day thing.

  13. The Following User Says Thank You to bradyjfrey For This Useful Post:

    alex357 (02-08-2010)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •