Page 1 of 2 12 LastLast
Results 1 to 10 of 12
Like Tree36Likes

Thread: Possible solution to difficult situation in honing

  1. #1
    Junior Member racer's Avatar
    Join Date
    Dec 2016
    Location
    UK
    Posts
    10
    Thanked: 4

    Default Possible solution to difficult situation in honing

    Hi

    Many forums have threads that say "I'm trying to hone but nothing works. The razor just
    won't become sharp" or such where beginners have do everything according to guides but still
    the razor is dull. I had a similar situation. A razor that has a mirror edge that's dull and i
    actually could pull a arm hair with its root when the hair was over the razors edge. The hair
    was bent but not cut.

    Here's a photo
    Name:  Mirror Edge.jpg
Views: 250
Size:  26.5 KB

    It's a razor edge honed with 400 grit, 3000 grit and few minutes with 10.000 grit.
    It has a shiny mirror edge. The blade looks bent but actually it's light playing around
    with the polished edge. But so dull.

    Then. I took a photo from a DE blade
    Name:  Gillette 7.jpg
Views: 242
Size:  31.2 KB

    The difference was that the actual tip of the razor has a "cutting edge" or how
    should it be described. Think that's the part that does the cutting as opposed to a single form
    bevel that's does not have a separate "knife edge" on tip.

    So next, about 400 laps with 10.000 grit stone
    Name:  AfterHighGrit.jpg
Views: 241
Size:  29.2 KB

    And same kind of "knife edge" appeared to the razor. I'm quite sure this is not a double bevel
    resulting from honing with and without tape because i had that issue. It was resolved with
    resetting bevel with low grit honing.

    So now i tested with putting shave cream on small part of arm hair and the straight razor shaved the area
    completely hairless.

    So my theory is that when a razor is "properly" honed but mysteriously dull the reason MAY be that
    the "knife edge" on top of bevel is missing. I assume that the knife edge is necessary because DE blades
    have them.
    Substance and Addison like this.

  2. #2
    Moderator rolodave's Avatar
    Join Date
    Aug 2011
    Location
    Racine, WI USA
    Posts
    7,531
    Thanked: 1927
    Blog Entries
    1

    Default

    In the first pic, the bevel is not set. Watching some of gssixguns honing vids will help you get the bevel set.

    400 laps on any stone is a lot. As I put your first post, get with someone near you for some hands on help.

    http://straightrazorpalace.com/memberlist.php?do=search
    Geezer and Chevhead like this.
    If you don't care where you are, you are not lost.

  3. #3
    Senior Member blabbermouth Kees's Avatar
    Join Date
    Jun 2006
    Location
    The Netherlands
    Posts
    5,474
    Thanked: 656

    Default

    Two things. 1.: you don't mention stropping before testing the edge. Many beginners ruin the edge with poor stropping technique. Moreover: you need to strop before testing the edge. You shouldn't test the edge straight off the hone. The cutting edge only reaches its full potential after proper stropping.
    2.: a few minutes or 400 laps on the 10K is enough to create a wire edge.
    And yes: as rolodave says: the bevel in pic 1 needs some more work.
    Last edited by Kees; 01-02-2017 at 08:19 AM.
    Chevhead likes this.
    Plus ça change, plus c'est la même chose. Jean-Baptiste Alphonse Karr.

  4. #4
    Junior Member racer's Avatar
    Join Date
    Dec 2016
    Location
    UK
    Posts
    10
    Thanked: 4

    Default

    I did strop for 25 laps before testing.

    So my mystery "knife edge" is actually a wire edge.
    Back to the drawing board, then.
    rolodave likes this.

  5. #5
    Senior Member alpla444's Avatar
    Join Date
    Sep 2010
    Location
    St Helens, uk
    Posts
    678
    Thanked: 96

    Default

    yes 400 laps is a lot esp as you are new to honing (ie maybe not all of the 400 laps where good laps, a couple of duff passes here and there would be counter productive for sure, as is the jump from 3k-10k stone thats a big jump for sure,)

    Do you have a Jewellers loupe?? they are cheap and very quick to use to check the edge while honing.

    Where are you in the UK?

    I am Merseyside based, if you are local or want to travel you are welcome to come over for some pointers etc.....
    Euclid440 and eddy79 like this.

  6. #6
    Senior Member blabbermouth
    Join Date
    Mar 2012
    Location
    Thunder Bay, Ontario, Canada
    Posts
    17,250
    Thanked: 3221

    Default

    You can watch all the vids on honing you want and think you are doing it right but the reality is you are not. Plain and simple, your bevel is not set as in the 2 planes of the bevel have not meet to form an edge. Without a proper bevel set going up the hone progression is like polishing a turd. I know this from having to learn honing on my own and went through the same thing. In the beginning you also don't know what to look for and/or how to interpret what you are seeing. That takes a while to learn too. The absolute best way to learning honing is to get together with a member who is experienced in honing for some one on one instruction.

    Personally I think you are creating far more work for yourself by using a 400 grit hone as a bevel setter. That is especially so if the blade has no chips and even then a 1K is all you need. If a bevel needs no major work, like removing chips, just a reset then a 3K should do the job. That leaves far less deep striations to remove than a 400 grit hone.

    To jump from a 400 grit hone to a 3K and finish on a 10K hone is too wide a spread between hone grits. I'd try using the 3K as your bevel setter and get a 5K or 8K to fill the gap between the 3K and 10K hones.

    In the end though I would really find a mentor for one on one instructions on honing. You can't believe how much I would have liked to have that option.

    Bob
    Life is a terminal illness in the end

  7. #7
    Senior Member blabbermouth eddy79's Avatar
    Join Date
    Feb 2013
    Location
    Gosnells Perth Western Australia
    Posts
    7,042
    Thanked: 656

    Default

    I would suggest using the 3k for longer. Looks like quite a bit of deep striations still likely from the 400. These will likely lead to a chippy harsh edge. Kill the edge and reset the bevel on the 3k. After removing all the deep striations then move on to the 10k. It will take a bit as it is a big jump but is doable. Make sure you keep your pressure light so as not to flex the blade or your honing wont reach the edge.
    My wife calls me......... Can you just use Ed

  8. #8
    Senior Member blabbermouth
    Join Date
    Dec 2014
    Location
    Virginia, USA
    Posts
    2,224
    Thanked: 481

    Default

    Others have pretty much hit the nail on the head. That's an intentional secondary bevel on the DE. What you have on your blade looks like either a burr/foil edge, or an unintentional secondary bevel because yours isn't quite set. Just to reiterate, 400 grit is far too coarse. Blade restoration/chip removal only. You want a good 1K, or a lot of time on the 3k.

    You also didn't mention what type of hone you're using. A Naniwa 3k and a Weiwei 3K are not the same. The former is a 3K and the latter more like a 1.5K, or so it's been described by users that own both sets. The same trend follows to the 8K and likely to the 10 as well.

    It will probably take a while, but were I using the same hones I'd probably drop down to the 3K and make sure that bevel was set properly. Maybe look into getting a good 1K (anything from naniwa, shapton glass/pro, Norton, King).

    Most of the problems new guys run into fall into 2 categories - bevel not set and uniform, and too much pressure used while honing. Sometimes the 2 go hand in hand.
    rolodave, BobH, eddy79 and 2 others like this.

  9. #9
    Junior Member racer's Avatar
    Join Date
    Dec 2016
    Location
    UK
    Posts
    10
    Thanked: 4

    Default

    Gentlemen
    Thank you for your passionate and good advices.

    I believe learning is a process where progress is made by making
    mistakes AND not repeating them. Todays theory of "knife edge" on top
    of bevel was debunked. I did manage to shave with it, not a perfect shave but
    a shave still.

    A 8000 grit stone is ordered and in the mail. I use the generic chinese ones from
    aliexpress as, well, i still have no clear idea what i really need an what not. Whenever
    i know what i'm doing i'll get decent stones and some beautiful gold etched straight razor
    but meanwhile as learning is done, razors overhoned and stones used unevenly because
    of perhaps wrong type of honing i'll stick to the cheap ones.

    And for a last comment there was no way to guess DE blades have an intentional
    double bevel. Thank for that information.
    rolodave, Marshal and Addison like this.

  10. #10
    Senior Member blabbermouth
    Join Date
    Dec 2014
    Location
    Virginia, USA
    Posts
    2,224
    Thanked: 481

    Default

    Yeah, I wouldn't have known either if I hadn't seen really close up pictures of them. I think with mass manufactured DE blades it's easier to go in shallow to get an edge roughed out, then come in a little steeper with a finishing grit to put that final shaving edge on it. Kind of like a mechanized version of the unicot process where you intentionally add a layer of tape at the finishing phase to get that secondary bevel.

    You can mimic it with your straights if you like, just add a layer or 2 of tape or a similar buffer to lift the spine a touch. I don't do it myself, but I've read a few guides and seen where others like the results. YMMV. But the bevel has to be fully set first.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •