Page 1 of 4 1234 LastLast
Results 1 to 10 of 32
Like Tree40Likes

Thread: Scary First Time Straight Shave

  1. #1
    Senior Member Panama60's Avatar
    Join Date
    Aug 2016
    Location
    Earth
    Posts
    358
    Thanked: 98

    Default Scary First Time Straight Shave

    Finished cleaning up my Shumate 135 earlier today and took it through the stones (1k, 4k & 8k) this evening.
    30 laps on the linen, 50 laps on each side of the leather and studied the edge with a 16x loupe. A couple of pits
    remain in the edge, but overall it looks good and smooth. Curiousity got the better of me and I couldn't wait
    until morning for the test shave. Hot towel prep. Vintage Colgate lather applied with a Van der Hagen boar brush.
    Couple of small nicks, need to figure how to trim around the van dyke. All in all, scary..., but what a thrill!


    Not a BBS shave by no means. In fact, the left side of my neck is still furry, hahaha!
    32t, Hirlau, BobH and 4 others like this.
    Rog

  2. The Following User Says Thank You to Panama60 For This Useful Post:

    Steel (11-17-2016)

  3. #2
    Senior Member blabbermouth Hirlau's Avatar
    Join Date
    Dec 2010
    Location
    South Florida
    Posts
    13,530
    Thanked: 3530

    Default

    Now, you just work on improving one element at a time. A slow, wonderful journey ahead.
    BobH, Euclid440, MJC and 1 others like this.

  4. #3
    Senior Member blabbermouth
    Join Date
    Mar 2012
    Location
    Thunder Bay, Ontario, Canada
    Posts
    17,250
    Thanked: 3221

    Default

    Congrats. Now just take it slow and easy from here. Don't get over confident when things start to really come together either. Enjoy the journey.

    Bob
    Life is a terminal illness in the end

  5. #4
    Senior Member BanjoTom's Avatar
    Join Date
    Aug 2010
    Location
    Fort Lauderdale
    Posts
    718
    Thanked: 160

    Default

    Ok Marine. Your journey has begun. If the edge of your razor is uneven I'd suggest going back to your 1 K and reset the bevel. Go lightly here as you move across the stone and check your edge under a strong light. Don't need a loupe to do this. Make sure that there are no shiny parts on the edge. If there are, go back to the 1 K hone and gently polish them out. Then do pyramids on the 4/8 hone to polish out the stryations of the 1 K.
    Good luck and Semper Fi!
    criswilson10 likes this.
    Proper prior planning prevents piss poor performance.

    Tom

  6. #5
    Senior Member Wayne1963's Avatar
    Join Date
    Feb 2013
    Location
    South Carolina, USA
    Posts
    1,181
    Thanked: 162

    Default

    Are you learning to hone, whilst learning to straight shave? If so, I'd learn to shave first and save the honing for later.

  7. #6
    Senior Member Panama60's Avatar
    Join Date
    Aug 2016
    Location
    Earth
    Posts
    358
    Thanked: 98

    Default

    Quote Originally Posted by Wayne1963 View Post
    Are you learning to hone, whilst learning to straight shave? If so, I'd learn to shave first and save the honing for later.
    I've been learning a lot the past few months and I'm grateful to every member of SRP for what I've learned.
    I thought about buying a shave ready SR online, but was enamored with the thought of finding a SR in the
    wild and bringing it back to service with my own hands. I now have 3 SR's ready to send off for honing, but
    something about this Shumate's 135 said "I'm the one". Light as a feather, round point, 11/16, hollow ground,
    this is my "beginner" I've been looking for. I took it to my new Norton stones and paid very close attention to
    each lap, all the time thinking about what I've read about here on the forum and the videos I've watched.
    Am I flat to the stone? Is my pressure to heavy? What does the edge look like, fresh metal, pits gone? I was
    focused. I studied the edge and was happy with it. For the HHT, I used my chest hairs holding the blade about
    a half inch off the skin, very little grab as the hairs caught the edge and popped off. What a lovely "tinking"
    sound it made. I knew my "beginner" was ready and so was I, to begin this part of my journey.
    Name:  Shumate135BladeFr.jpg
Views: 274
Size:  29.6 KB
    Name:  Shumate135FullFr.jpg
Views: 291
Size:  52.1 KB
    Name:  Shumate135PittingFr.jpg
Views: 268
Size:  29.2 KB
    Name:  Shumate135Zed.jpg
Views: 292
Size:  43.3 KB
    Rog

  8. #7
    Senior Member BanjoTom's Avatar
    Join Date
    Aug 2010
    Location
    Fort Lauderdale
    Posts
    718
    Thanked: 160

    Default

    I'm proud of you Marine. Good job. You know what you are doing and where to get help on the journey.
    Steel likes this.
    Proper prior planning prevents piss poor performance.

    Tom

  9. #8
    Senior Member Panama60's Avatar
    Join Date
    Aug 2016
    Location
    Earth
    Posts
    358
    Thanked: 98

    Default

    Second SR shave, not so scary this time...

    Prep: Hot shower
    Lather: Vintage Colgate (I think it's a magic puck that'll never wear out, hahaha)
    Brush: VDH badger with a loose knot
    Weapon: My trusty Shumate's 135
    Mantra: "shave the lather...sfave va laver...snaff a afur..."
    Clean up DE: Micro Touch One w/ASTRA platinum blade
    Post: Nivea Sensitive Post-Shave balm
    Shave: BBS! Yea, baby! One new nick.

    Went at it a little different this morning. Started on the left side instead of the right. (Right hand dominant)
    Applied pressure in the hairline above the sideburn, 2 short strokes and I reapplied pressure on my upper
    cheek near the ear. It gave me a lot more control of the skin in that area. Same on the right. Skipped the
    jaw line and went for the throat. Same here, clear a spot and reapply pressure. Can't go WTG or ATG, so
    south and north strokes for now. Then the jaw lines. Plenty of spots to apply pressure and tried a scythe
    stroke. (A curving stroke? Not really sure on what it would be called.) Learned to forget the grain and pull
    into the van dyke. Tried to place, roll for angle and pull away from the beard. NOPE! NICK! Don't roll with
    a SR you.....that's a DE move if there ever was one! 2 passes with the Shumate and then a 3rd with my
    DE ATG. BBS! I won't shave again until day after tomorrow.

    And to think, all those times I shaved twice a day (in the svc) just because I didn't know how to shave.


    Just noticed I have been saying my VDH brush is boar, it's a badger...
    Last edited by Panama60; 10-20-2016 at 07:16 PM.
    32t and BobH like this.
    Rog

  10. #9
    Senior Member gabrielcr78's Avatar
    Join Date
    Oct 2016
    Posts
    983
    Thanked: 134

    Default

    wow!! that's a very nice looking blade after your work congrats!

  11. #10
    Senior Member AcesandEights's Avatar
    Join Date
    Aug 2016
    Location
    Cowden, Il.
    Posts
    436
    Thanked: 131

    Default

    Quote Originally Posted by Panama60 View Post

    Mantra: "shave the lather...sfave va laver...snaff a afur..."

Page 1 of 4 1234 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •