Page 1 of 2 12 LastLast
Results 1 to 10 of 13
Like Tree3Likes

Thread: Last minute advice

  1. #1
    Junior Member
    Join Date
    Apr 2014
    Posts
    9
    Thanked: 0

    Default Last minute advice

    Hey all,
    I just got as a present new dovo best quality 5/8 (after i already bought a Giesen & Forsthoff). I know it was honed.
    I am just about to go and shave with it for the first time (this is my first straight razor shave!).
    So as preparation, i saw Mr. Lynn Abrams video on:
    Stropping for beginners:
    Shaving for beginners:
    And i have several questions.
    1) about stropping i have what i think is a loom strop but its very thin (i think about 2 inch maybe?) so each time i go over with the razor i don't really cover the whole edge. What is the best way to cover thee whole edge?
    2) in the "Shaving for beginners" video, Mr Abrams advised for the first shave to just from the sideburns to the jaw. I was wondering if you guys could give me some more advice, things to be more attentive to, technique and any other info that could help.
    Thanks in advance.

  2. #2
    Senior Member Splashone's Avatar
    Join Date
    Sep 2013
    Location
    Tucson, AZ
    Posts
    1,031
    Thanked: 176

    Default

    If you have a razor that arrived shave ready (that means it went to someone that honed it, not the factory edge), I hope you didn't strop it before first use.

    Lynn's video is about the best out there and very thorough. What specific questions do you have?

    Go to the library on this forum and check out the videos and resources for beginners. They cover everything from shaving to stropping. Come back here if you still have questions.
    The easy road is rarely rewarding.

  3. #3
    Senior Member blabbermouth edhewitt's Avatar
    Join Date
    May 2013
    Location
    Perth Australia
    Posts
    7,741
    Thanked: 713
    Blog Entries
    1

    Default

    For stropping on a narrow strop you use a technique called the "X"stroke, if you go to the videos section and look up afdavis's stropping videos they are very good.
    As for your second question, concentrate on good prep, then allow plenty of time, dont use pressure, and keep a low angle, DO NOTmove the blade side ways on your face - it will end badly.
    And as soon as you feel uncomfortable stop.
    Tankus likes this.
    Bread and water can so easily become tea and toast

  4. #4
    Senior Member showmeshiner's Avatar
    Join Date
    Dec 2013
    Location
    missouri
    Posts
    125
    Thanked: 7

    Default

    Slow and steady. Try to use no pressure. Take the lather off your skin without pressure on your face. Cut hair don't scrape it off
    Tankus likes this.

  5. #5
    Junior Member
    Join Date
    Apr 2014
    Posts
    9
    Thanked: 0

    Default

    well,
    I'm done with my first experience, And i must say, its harder than it looks.
    I have to say that i nicked my self a bit (maybe i put too much pressure or the angle was off or the movement was not good) but i'll take it as a "right of passage". I guess that i'll get better as a shave more.
    I shaved only the sideburns to the jaw - and i didn't really get the smooth sensation that people talk about. (maybe my beard was too long to begin with?). I finished the rest of my face with my regular gillette razor.
    Should I try again tomorrow or wait several days?
    What are the proper steps to clean the razor after use? wash with water and wipe it with a dry towel?
    Thank

  6. #6
    Senior Member showmeshiner's Avatar
    Join Date
    Dec 2013
    Location
    missouri
    Posts
    125
    Thanked: 7

    Default

    I dry them carefully. Leave open to dry for 30 min then oil lightly and store.

    P.s. sounds like it could've gone worse. As for the smoothness of the shaving. Could be razor or could be a million other things. Lather is very important. It can make or break it for my tough beard. And other countless variables.
    Last edited by showmeshiner; 04-17-2014 at 03:58 PM.

  7. #7
    Junior Member
    Join Date
    Apr 2014
    Posts
    9
    Thanked: 0

    Default

    Thanks for the advice and support.
    Unfortunately i still didn't get the soap and brush so im using regular shaving gel (according to the notes here - its better than nothing).
    About the post cleaning - what kind of oil do you use?
    Thanks again.

  8. #8
    Senior Member showmeshiner's Avatar
    Join Date
    Dec 2013
    Location
    missouri
    Posts
    125
    Thanked: 7

    Default

    I'm not sure what everyone else uses but I take a drop of neatsfoot oil or a quick spray of remoil. Then wipe.

  9. #9
    Stay calm. Carry on. MisterMoo's Avatar
    Join Date
    Jul 2013
    Location
    Lizard Lick, NC
    Posts
    1,316
    Thanked: 184

    Default

    Blade already in motion before it touches skin; blade still in motion when it's lifted.



    Blade never still on skin, gwasshoppuh.

    Good luck - have fun.
    "We'll talk, if you like. I'll tell you right out, I am a man who likes talking to a man who likes to talk."

  10. #10
    Senior Member deepweeds's Avatar
    Join Date
    Apr 2006
    Location
    Evanston Illinois
    Posts
    656
    Thanked: 97

    Default

    On the question whether to wait a day: that can be a good idea, especially starting out. We're harder on the skin as beginners (too much pressure, harsh blade angles, buffing over and over on one spot), and irritation adds one more unpleasant variable to the learning curve.
    Keep your pivot dry!

Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •