Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Junior Member
    Join Date
    Jul 2008
    Location
    California
    Posts
    13
    Thanked: 0

    Default 3M wet dry vs. micro-mesh grits

    How do the grit numbers compare between wet dry and micro-mesh? I bought some micro mesh but even the highest grit doesn't seem higher than 2k of the 3M.

    No matter what I use I can't seem to get rid of very fine scratches while polishing. I am using compounds with a buffer as well. I thought the micro mesh would help but it doesn't seem to.

  2. #2
    Senior Member Buddel's Avatar
    Join Date
    May 2007
    Location
    Germany
    Posts
    523
    Thanked: 203

    Default

    The 1500 Micro Mesh compares approx. the 600 grit from the 3M. So the 12.000 MM is approx. 5000 at normal grits.

  3. #3
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    Fine scratches on what???
    The blade??
    or the scales????

  4. #4
    Dapper Dandy Quick Orange's Avatar
    Join Date
    Mar 2007
    Location
    Centennial, CO
    Posts
    2,437
    Thanked: 146

    Default

    I'm going to say that there's something in your micromesh or on your surface. You shouldn't have any scratches with the highest micromesh.

  5. #5
    Junior Member
    Join Date
    Jul 2008
    Location
    California
    Posts
    13
    Thanked: 0

    Default

    Quote Originally Posted by gssixgun View Post
    Fine scratches on what???
    The blade??
    or the scales????
    Yes the blade. I go back down the line of grits thinking that I didn't get out all the scratches from the lower numbers and go back up but still see lines. Is a glass finish really doable or am i being unrealistic?

  6. #6
    The Shell Whisperer Maximilian's Avatar
    Join Date
    May 2008
    Location
    Sin City
    Posts
    5,597
    Thanked: 3384

    Default

    Quote Originally Posted by radray5 View Post
    Yes the blade. I go back down the line of grits thinking that I didn't get out all the scratches from the lower numbers and go back up but still see lines. Is a glass finish really doable or am i being unrealistic?
    A glass mirror finish is doable, no doubt but when sanding you need to remove the scratches from the previous grit. It seems somewhere in your sanding pyramid you left scratches that were not properly removed. When some leftover scratches are present you can go to town with your 12000 Mesh or green compounds, you'll achieve a nice polished look but the scratches will remain.
    Unless your buffing wheel is contaminated with some lower grit compounds or for some reason your sand paper is. When moving up in the grits be it sand paper or buffing wheels always make sure the blade is as clean as possible.

    əˌfisyəˈnädō | pərˈfekSH(ə)nəst | eS'prəSSo | düvəl ləvər

  7. #7
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    Personally I have never had much luck with Micromesh on the steel, that's why I was asking, it works great for me on the finish on the scales, but that is about it...
    Maybe Mad Max can give you some help on how he uses it, but I switch to the Buffer and compounds after 2000 grit wet-r-dry....

  8. #8
    Junior Member
    Join Date
    Jul 2008
    Location
    California
    Posts
    13
    Thanked: 0

    Default

    Thank you all for the input. I agree with Glenn the micro-mesh seems like a good idea but I don't see much effect above 2k 3M.

    And I think you are right Max, I am thinking my buffing wheels need to be changed. The lines are VERY fine and the buffing should be removing them.

    The only thing I can think of is contamination, although I keep them separate with different compounds maybe it is sawdust or too much compound on the wheels. I am at the point of getting the blade VERY shinny but those fine lines won't go away. I guess when all else fails, start from scratch.
    Last edited by radray5; 04-07-2009 at 08:40 AM.

  9. #9
    Senior Member Buddel's Avatar
    Join Date
    May 2007
    Location
    Germany
    Posts
    523
    Thanked: 203

    Default

    I agree with Glen, in my opinion MicroMesh is not the first choice for steel. I´m shure the higher grits from MM dont will work effectiv on the steel, thats why you dont can notice a different to the 3M. For Wood, Horn, Bone and this stuff it is great, for steel you will get better results with the 3M and good buffing compounds.

  10. #10
    The Shell Whisperer Maximilian's Avatar
    Join Date
    May 2008
    Location
    Sin City
    Posts
    5,597
    Thanked: 3384

    Default

    Quote Originally Posted by gssixgun View Post
    Personally
    Maybe Mad Max can give you some help on how he uses it, but I switch to the Buffer and compounds after 2000 grit wet-r-dry....
    I don't use Micro Mesh anymore since it's all buffer, polishing, buffing and compounds. That's quality stuff, right there.

    Like everybody said, it works great on scales if needed, especially the acrylics, horn, bone or poly or any glossy coating you have applied on wood, ...

    I always test all my products. These were my finding with Micro Mesh.
    When I have a mirror polished blade coming from the buffer (scratch free) and I swipe it with a 12K micro mesh the blade incurs scratches.
    That's why I stopped using it on steel.
    Last edited by Maximilian; 04-07-2009 at 02:02 PM.

    əˌfisyəˈnädō | pərˈfekSH(ə)nəst | eS'prəSSo | düvəl ləvər

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •