Results 1 to 10 of 10
Like Tree19Likes
  • 9 Post By gssixgun
  • 1 Post By dirtychrome
  • 6 Post By celticcrusader
  • 3 Post By karlej

Thread: The Illustrated Guide to Sleeving an Oversized Pivot...

  1. #1
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default The Illustrated Guide to Sleeving an Oversized Pivot...

    I needed to sleeve this W&B before pinning the scales so I tried to get some pics done... I apologize for the final pic I even took two and they both sucked...

    When you have an over-sized pivot hole you need to fill that space, you have some options here, some people fill the entire hole with epoxy and then re-drill the hole, some use a combination of a sleeve and the epoxy... Myself I just sleeve it as close as I can get it .... My theory is that these razors have been riding around on 1/16 rods for about 100 years so any thing tighter will probably last another 100 years.... I have a few different sizes of brass tubing in the shop starting with this stuff with a 1/16 ID hole, all of them slip into one another, so I can increase the size of the OD without any trouble (I use the same principle for making brass center pins)
    Once the razor is ready to pin I chose the closest sized tubing to the hole, sometime like this razor, I only have to use one sleeve, sometimes two..

    Name:  sleeve 1.jpg
Views: 2955
Size:  45.9 KB

    I cut the tubing to approximate size so it will fit inside the tang without rubbing...

    Name:  sleeve 2.jpg
Views: 2799
Size:  45.1 KB

    I fit it, then smooth up the edges

    Name:  sleeve 3.jpg
Views: 2812
Size:  47.4 KB

    The easiest way I have figured out to do this is to put the sleeve over the pin first (note the bearing washer under the sleeve)...

    Name:  sleeve 4.jpg
Views: 2907
Size:  38.3 KB

    Put the razor on, then another bearing washer, then scale and pin as usual....

    Name:  sleeve 5.jpg
Views: 2814
Size:  28.1 KB


    This is a fast simple solution to over-sized pivot holes, you can probably do without this but as the razor moves and loosens in the scales you can run into problems with the edge hitting the scales and/or wedge it is just way easier to just throw a fast sleeve in there and eliminate any of these problems before they arrise...
    Last edited by gssixgun; 02-23-2009 at 01:37 AM.

  2. The Following 22 Users Say Thank You to gssixgun For This Useful Post:

    2Sharp (02-23-2009), Alfonnso (05-24-2012), baldy (09-10-2010), BigJim (03-16-2011), Buckler (09-09-2010), Chevhead (10-10-2013), Cove5440 (04-13-2012), DMHarper (03-16-2011), FatboyQ (04-02-2014), Geezer (07-29-2010), JackofDiamonds (08-21-2012), JBHoren (10-17-2013), JOB15 (06-21-2018), JP5 (06-09-2015), ne0nblakk (12-24-2013), peribeca (03-12-2012), randydance062449 (02-24-2009), shutterbug (03-18-2011), singlewedge (02-23-2009), Slawman (12-05-2015), Str8Raz0r (05-26-2011), WadePatton (12-10-2013)

  3. #2
    Senior Member singlewedge's Avatar
    Join Date
    Sep 2008
    Location
    PDX
    Posts
    1,568
    Thanked: 203

    Default

    You have my razor that I am going to have to do this with. So thanks cause I was gonna ask sooner or later.

  4. #3
    Some kind of Zombie BigJim's Avatar
    Join Date
    Feb 2011
    Location
    Le Mars Iowa
    Posts
    1,019
    Thanked: 166

    Default

    I know this is an old thread, but: I'm new to working with tubing this small and soft. Brake tubing is about as small as I work with and that's many times bigger and harder than small brass tubing. What did you use to cut the brass tube without making it out of round? I need to fix a worn out pivot hole in a razor and was directed to this thread as an option for fixing it.

    Thanks!

  5. #4
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    I use a hack saw 24tpi and almost no pressure,,, then file it smooth

  6. The Following 2 Users Say Thank You to gssixgun For This Useful Post:

    BigJim (03-16-2011), peribeca (03-12-2012)

  7. #5
    Some kind of Zombie BigJim's Avatar
    Join Date
    Feb 2011
    Location
    Le Mars Iowa
    Posts
    1,019
    Thanked: 166

    Default

    Thanks.

    Wasn't sure if a 24tpi hack saw would be too aggressive for that tubing. I'm not familiar with how soft it is.

  8. #6
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    Jim I look for this display in the Hardware store and get everything from it

    it is from K&S metals an found in many stores

    hmm can't get the website to come up will try later


    http://www.ksmetals.com/retail.html
    Last edited by gssixgun; 11-26-2013 at 04:12 PM.

  9. #7
    Senior Member dirtychrome's Avatar
    Join Date
    Mar 2010
    Location
    Arizona
    Posts
    652
    Thanked: 408

    Default

    I use a utility knife/box cutter to cut the tubing. Just kinda roll tubing over flat surface, similar how a tubing cuter would work if a small enough one could be found.

    For tubing and rod sizes, (copy paste from other post I did)

    K & S Engineering - popular display case at Ace hardware and other places.
    Here are some part numbers if you want to try online like Amazon or someplace.

    If need brass tube for ovaled out pivot hole the following:
    What I have still with labels:

    part number 8126 3 pack sku 14121 18126 1/16 ID, 3/32 OD - it will slide into
    part number 127 Single item sku 14121 10127 it will slide into
    part number 128 Single item sku 14121 10128

    Stock# 8125 3 pack 1/16 OUTSIDE Diameter if a need for that small

    For brass rod
    part number 8162 brass rod 3pack 12" long
    part number 1162 5pack 36" long
    I think 162 would be for a single 12", but I have never used/found it.

    I would guess 3 pack part numbers have the '8' at the front of part number, and single item is 3 digit PN? So would suspect 129 would slide over 128 if you had that as a need.

    By same logic, if they do single rod 1/16 rod, probably part number 162?
    Robbied likes this.

  10. The Following 4 Users Say Thank You to dirtychrome For This Useful Post:

    Clayglen (12-28-2015), Nphocus (04-22-2011), peribeca (03-12-2012), WadePatton (12-10-2013)

  11. #8
    Senior Member celticcrusader's Avatar
    Join Date
    May 2011
    Location
    Merthyr Tydfil South Wales UK.
    Posts
    5,601
    Thanked: 1413

    Default

    I found a tube from a cotton ear bud to be a perfect size for most over large pivot holes, i've used it works very well also being hard nylon wear dosen't seem to be an issue, fits snugly and easy to cut with a stanley knife.

    Jamie.

  12. The Following 3 Users Say Thank You to celticcrusader For This Useful Post:

    jmercer (02-09-2015), JOB15 (06-21-2018), RADisorder (05-01-2013)

  13. #9
    Senior Member karlej's Avatar
    Join Date
    Oct 2011
    Location
    Standish, Maine
    Posts
    816
    Thanked: 952

    Default

    I learned a trick to cut steel pins and small parts from an old master gunsmith. Lay/stick a piece of scotchtape on the bottom side of the pin and use a dremel cutoff wheel to cut the pin. If you go easy toward the end of the cut it ends just hanging on the tape. If you go too far it falls on the tool bench or floor stuck to the tape and is easy to find. I've had a chance to sleeve 1 restore so far following this guide in the stickies and used this method to cut the tube. Worked slick.
    Hope this helps,
    Karl
    Chevhead, Robbied and Slawman like this.

  14. The Following 2 Users Say Thank You to karlej For This Useful Post:

    ajkenne (12-28-2015), Slawman (12-05-2015)

  15. #10
    Senior Member Willisf's Avatar
    Join Date
    Sep 2014
    Location
    Yorkton, Saskatchewan, Canada
    Posts
    1,171
    Thanked: 230

    Default

    Old thread...worth bumping!
    Is it over there or over yonder?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •